retz工业/美国瑞茨,我们一直致力于流体控制领域的持续创新,始于2005……浮动式,固定式气动法兰球阀用于输送粘性、易结渣介质管道上的球阀应使用全通径的,方便定期的刮蜡吹扫器通过,驱动方式为气动双作用,气动单作用、带手动气动作用,气动调节型,防爆气动球阀floating and fixed pneumatic flange ball valves are used for conveying viscousand easily slagging media. ball valves on pipelines should be full bore,convenient for regular wax scraping and blowing through. the driving method ispneumatic double acting, pneumatic single acting, with manual pneumatic action,pneumatic adjustment type, explosion-proof pneumatic ball valve
进口气动法兰球阀产品详情product details
气动法兰球阀的阀座多选用聚四、对位聚苯等高分子聚合材料,密封性能好,但材料相对较软。由于进口气动法兰球阀2.jpg材料较软,但又要达到一定的密封比压,势必增加启闭扭矩,为了尽量改善此种情况,retz采用双斜面弹性密封圈或v形槽弹性密封圈结构设计,利用管道内压力推动球体,帮助密封。当介质压力较小时,密封圈与球体接触面积较小,故有较大的密封比压,确保可靠密封。介质压力较大时,密封圈与球体接触面积增大。故密封圈能承受较大的介质推力而不会损坏。对于工作压力很低的球阀,考虑到介质压力不能确保阀座可靠密封,而预紧力长期使用后又会衰减,故对于低压、压或真空工况用球阀,采用弹簧加载的阀座密封结构,能确保球阀长期可靠的密封 retz品牌 (floating type,fixed type) the valve seat of pneumatic flange ball valve is mostly made ofpolymer materials such as polytetrafluoroethylene, counterpoint polystyrene,which has good sealing performance, but the material is relatively soft. sincethe material is relatively soft, but also needs to reach a certain sealingspecific pressure, it is bound to increase the opening and closing torque. inorder to try to improve this situation, retz adopts the structural design ofdouble bevel elastic seal ring or v-groove elastic seal ring, and uses thepressure in the pipeline to push the ball to help seal. when the mediumpressure is small, the contact area between the seal ring and the ball issmall, so there is a large sealing specific pressure to ensure reliablesealing. when the medium pressure is large, the contact area between the sealring and the ball increases. therefore, the seal ring can withstand largemedium thrust without damage. for the ball valve with very low workingpressure, considering that the medium pressure cannot ensure the reliablesealing of the valve seat, and the preload will decay after long-term use, thespring loaded valve seat sealing structure is adopted for the ball valve withlow pressure, ultra-low pressure or vacuum conditions to ensure the long-termreliable sealing of the ball valve
进口气动法兰球阀特点characteristic
1、采用全通径或缩径设计,流通阻力小 fullbore or reduced bore design, low flow resistance
2、采用高平台结构,iso5211连接标准,能使安装电/气动执行器更为化 high platformstructure and iso5211 进口进口气动法兰球阀3.jpgconnectionstandard are adopted to make the installation of electric/pneumatic actuatorsmore professional
3、阀杆采用内装式,轴肩及聚四(或增强石墨)推力垫结构防止阀杆因管道内压力 而吹 出,同时聚四(或增强石墨)材料减小阀门的启闭扭矩,使操作更为省力 the valve rod isof built-in type. the shaft shoulder and ptfe (or reinforced graphite) thrustpad structure prevent the valve rod from blowing out due to the pressure in thepipeline. at the same time, the ptfe (or reinforced graphite) material reducesthe opening and closing torque of the valve, so that the operation is morelabor-saving
4、具有防火防静电结构,在阀杆与阀体及阀杆与球体之间设置导电弹簧,避免因静电打火点燃易燃介质。确保系统安全 ithas a fireproof and anti-static structure. a conductive spring is set betweenthe valve rod and the valve body and between the valve rod and the ball toavoid ignition of flammable media due to static electricity. ensure systemsecurity
5、耐火结构双重保护,当万一发生火灾而使密封圈烧损时,球阀的各个密封部位均能形成金属对金属的硬密封结构 thefire-resistant structure has double protection. in case of burning of thesealing ring in case of fire, each sealing part of the ball valve can form ametal to metal hard sealing structure
进口气动法兰球阀性能描述performance deion
公称通径dn(mm)
|
浮动式1/2”~8”、固定式2”~20”
|
公称压力(mpa)
|
pn1.6、2.5、4.0、6.4 mpa;ansi 150、300lb
|
允许压差(mpa)
|
≤公称压力
|
阀体形式
|
两段式铸造球阀
|
连接形式
|
法兰式
|
阀芯形式
|
"o"型球形阀芯,浮动式,固定式结构
|
密封填料
|
v型聚四填料、柔性石墨填料等
|
流量特性
|
近似快开型
|
动作范围
|
0~90°
|
泄露量q
|
小于额定kv0.01%
|
可调范围
|
250:1
|
350:1
|
控制方式
|
开关型(开关两位控制)、调节型(4~20ma控制)
|
执行器参数actuator parameters
执行器型号
|
at、ar、aw系列单、双作用气动执行器
|
供气压力
|
0.4~0.7mpa
|
气源接口
|
g1/4"、g1/8"、g3/8"、g1/2"
|
环境温度
|
-30~+70℃
|
作用形式
|
单作用执行机构:气关式(b)--失气时阀位开(fo);气开式(k)--失气时阀位关(fc)
双作用执行机构:气关式(b)--失气时阀位保持(fl);气开式(k)-- 失气时阀位保持(fl)
|
可配附件
|
、电磁阀、空气过滤减压器、保位阀、行程开关、阀位传送器、手轮机构等
|